People who install a ceiling fan do two things very well for their home:First they instantly upgrade the appearance of their homeSecond they improve air circulation.Your probably wondering well how do i install a ceiling fan?This guide will be walking you through the process, step-by-step, on how to install a ceiling fan.The Harbor Breeze ceiling fan and Hampton Bay ceiling fan are very functional and provide any room with added style. If a ceiling fan is going to be installed in a room that has a ceiling outlet already, then the wiring process is the same as wiring any other type of ceiling fixture.Now:If there is no overhead box in the room, an electrician will need to be hired to install the box and also run the wires across the ceiling and through the wall. You can install the actual fan on your own.Tip: For instructions on replacing a ceiling fan, check the owner’s manual for your specific model for removal instructions, and then use this guide to get your new model installed. If you dont have a guide then check out our range of guides on our. Make sure that the current ceiling box that you have can hold the weight of the new ceiling fan that you are installing.Here’s the deal:1. Inspect All Electrical Outlets.
Safety: Turn the power off to the fan at the electricalpanel before you start. Use a testing device to make sure that no power isbeing received by the fan.Inspect your current junction box to ensure that it is ratedto use with ceiling fans.
The box should have an inscription on it to indicatethat. Usually the box is metal. If it isn’t, it should be replaced with afan-rate junction box along with a fan brace placed in between the ceilingjoists in order to help support the weight of the fan. Step 2 will show this process.2. Mount Junction Box.
– Take the fan brace and insert it through a hole in thesheetrock and into the ceiling. Thebrace’s square tube needs to be centered with this hole.– Take the square tube and use your hand to rotate it untilits teeth are locked firmly into the joist.To gauge the results, feel around it.– Take the U-bolt bracket and attach it to the fanbrace. The bolts should be facingdownward and the bracket should be centered inside of the hole.– Take the cable wire and thread it into the junction box. The box should be slipped up so the bolts are able to slide through.
To secure the box in place, tighten the nuts.But here’s the kicker:3. Mount The Bracket. – Your ceiling fan wiring needs to be connected to your household wiring.
Additional wires come with some ceiling fans, so make sure you check the of your fan for specific instructions and check the ceiling fan wiring diagram. Use the wire nuts that come with the ceiling fan installation kit in order to secure all of the wires. If your ceiling fans do not have lights then this will be a much quicker process.– To wire the ceiling fan, make sure the wires are matched up. The green or copper insulated wire on the fan will often connect to the ground wire. The black wire on the fan’s motor connects with the supply’s black wires.
The light kit’s wire from the ceiling fan, which are striped or blue, connect as well with the supply’s black wires. The white wire on the fan’s motor connect with the supply’s neutral or white wire.Want to know the best part?If you dont have the correct parts or need help check out our– After these wires have been connected securely, they canbe pushed into the junction box.– If the wires don’t fit inside the box, you can cut themusing wire cutters. That will preventthem vibrating against the canopy while the fan is running.– Take the canopy and clip it to the mounting bracket, thentighten all of the screws.Tip: Follow the manufacturer’s instructions whenever you are wiring a ceiling fan to make sure you connect it properly. If you have any questions about wiring a ceiling fan, review the that go with your specific model of ceiling fan.This is crazy:6. Attach The Bulbs And Blades. – There are quick-install blades on some fans that make theinstallation process faster. The bladearm posts can be aligned through the keyhole slots on the blade and slide themoutwards until they click into place and lock.– For fans that do not have quick-install blades, the fanblades need to be screwed into the blade arms.Whatever side of the blade that you want to show should be facing down.– The installation process also can be speed up if you haveceilings fans that have accu-arm blade brackets.
Those brackets have blade screws that areattached. There is also an alignmentpost located on the bracket to help mount the blade arms without the mountinghole getting stripped.– For fans that do not have the accu-arm feature, there aretwo screws that are used to fasten the blade assembly onto the motor. The screws should be driven in slowly so thatthe blades are not bent or stripped in the process. Securely tighten the screws.– Install any light bulbs or globes that come with thekit.– Turn the power back on and test the wall controls and ceiling fan remotes to ensure that the fan turns on.Now:7.
Tips For Ceiling Fan Installation– Before you install your ceiling fan, check out the ceilingconditions in the place where you want to install the fan.– If you are installing a fan in a place where one didn’t exist before, check with the building code department in your local area to find out if you are required to get a permit.Remember Safety:– Safety: Ceiling fans must be anchored properly to an electric ceiling box that has been designed to be able to hold heavy fixtures. Not only will it be holding the ceiling fan’s wiring, but also will be supporting the fan’s full weight. If an existing ceiling fan is being replaced, double-check to make sure the new fan’s weight can be supported by your existing ceiling box.– Safety: Turn the power off to the fan at your electricalpanel. Then use the right testing deviceto make sure there is no power in the fixture before starting to do anywork. Don’t rely on your wall switch forprotection against electrical shock.– If you are installing a ceiling fan to replace a simplelight fixture, most likely you will need to replace the box with one that hasbeen rated to use with ceiling fans.– Consider getting an easy-install ceiling fan, which youcan install in only three simple steps.All of the parts that need to be assembly just click into place.– Before you install your ceiling fan, check the joists tosee if there are any plumbing pipes or wiring that are in the way.
Hampton Bay Ceiling Fan Light Wiring Diagram - Welcome, thank you for visiting this simple website, we are trying to improve this website, the website is in the development stage, support from you in any form really helps us, we really appreciate that. We will share this website for you articles and images of wiring diagrams, engine schemes, engine problems, engine diagrams, transmission diagrams, replacement parts, fuses, electrical diagrams, repair manuals, wiring harnesses, fuse boxes, vacuum diagrams, timing belts, timing chains, brakes diagrams, etc. In full, but still support us to improve this website.
Please take a look at the manuals below. These manuals are for the different Hampton Bay Ceiling Fan models. Just search for your model below and then click the link which will take you to the correct page for your particular model. Please note this is a free service so we would really appreciate it if you link back to us or Facebook share and like our page.
If you have a particular model that is not listed here then please make sure to add a comment below and we will search for your manual and then post it to this page.A link to this page from your website would be appreciated as its a good way to spread the word. Hampton Bay Tuxford Fan Manual –. Hampton Bay Trenton 52in Ceiling Fan Manual –. Hampton Bay Tahiti Breeze 52in Ceiling Fan Manual –. Hampton Bay St.
Regis 60in Ceiling Fan Manual –More Manuals below with HamptonLightingAdvice. Hampton Bay Spoleto 44in ceiling Fan manual –.
Hampton Bay Huntington III 52 in Ceiling Fan Manual –. Hampton Bay Model AC552 Ceiling Fan Manual –. Hampton Bay Covington Ceiling Fan 54-CVT –.
Vercelli 52 in. Ceiling Fan Hampton Bay Manual – l. Hampton Bay Caffe Patina 52 in. Caffe Patina Ceiling Fan Manual –.
Hampton Bay Windward II 54 in. Ceiling Fan Manual –.
Hampton Bay Windward IV 52in Ceiling Fan Manual –. Hampton Bay Altura 56in Ceiling Fan Manual –. Hampton Bay Campbell 53 inch Ceiling Fan Manual –. Hampton Bay Whitlock 44 in. Mediterranean Bronze Ceiling Fan Manual –. Hampton Bay Victoria 70 in.
French Beige Ceiling Fan Manual –. Westinghouse Contractors Choice 52 in. White Ceiling Fan manual –.
Southwind 52 in. Ceiling Fan Manual –. Hunter 55 in. Outdoor Gossamer Ceiling Fan Manual –.
Hampton Bay Sidewinder Ceiling Fan Manual –. Hampton Bay Landmark Ceiling Fan Manual –. Hampton Bay Brookdale 60in Ceiling Fan Manual –.
Hampton Bay Hawkins 44 in. Tarnished Bronze Ceiling Fan –. Hampton Bay Model # AG804-LN Winfield 54 in –. Hampton Bay Marta 52 in Brushed Nickel Ceiling Fan –. Hampton Bay Hayward 52 in Ceiling Fan –. Hampton Bay Model 728-046 heirloom 52in Ceiling Fan –. Hampton Bay Model AC 552 Ceiling Fan –.If you are unable to find your manual above then please leave a comment below and Facebook like this page.
Once you have Liked us on Facebook and left us a message we will then upload your manual for you.Please note when you click on a link above you will be taken to a page describing the ceiling fan along with information and descriptions and images. At the bottom of the page is a link you can click that will take you to a page where you can download the actual manual. Manuals are mostly in PDF format.If you are looking for lighting manuals then check out out page.Please also check our page if you have a Harbor breeze ceiling fan.if you need for your home windows the perfectwash is the right way to go.Please also check out if you are having problems with your ceiling fan remote.
Last week, I posted an article about successfully rewiring my remote control ceiling fan to bypass the remote and work off of the wall switch. I had a couple questions, and judging by the lack of help I was able to find online, I thought I would put the information out there.I am not a certified electrician. The instructions and method described below worked for me in my situation. I take no responsibility if you destroy your own ceiling fan, get a shock, blow a fuse, or cause other damage.
Modify electronic devices at your own risk (and at risk of voiding the warranty)The majority of this came from a forum onThe important information is here:However, if you purchased an Altura Oil Rubbed Bronze fan (from the Home Decorators Collection) at Home Depot. Same guts, same wiring, but the colors in your harness don’t match up. (link )Here is the conversion chart:If you’re looking at the front of the wiring harness coming from the fan, the wires should look like this:Here’s what you do:In this scenario, the Black wire is crimped together with the Brown and the ThinWhite. The gray wire at the fan is connected to the gray wire on the puck. The White and Blue wires at the fan are connected to the White wire at the Puck.If you have the add-on lighting kit, you will want to splice the White wire for the light to the White wire on the puck. If you want the light to come on when the fan comes on, connect the Blue wire from the light to the Black/ThinWhite/Brown combohowever, I wanted my light to run independent of the fan, so I connected it to the Red wire coming from the ceiling (which I had to feed down through the fan assembly to make connecting and disconnecting easier).note: in the above photograph, the red wire leading to the puck is a splice wire I had lying around, I did not have a scrap of gray wire.
Hampton Bay Fan Installation Instructions![]()
About PottsyFor nearly a decade, I hosted a morning radio show. I relocated, with my family, to Cleveland in 2006. The morning show routine of observing and commenting on the every day is a hard habit to break.
From January 2009 until September 2012, I was a stay-home dad, making notes of things I noticed about my surroundings, my children and myself. Now, I am back, working on another morning show, trying to balance kids, wife, job, dinner, scouts and all of the other curve-balls life throws into my juggling routine. This is my blog. The conversion outlined will require 2 switches and 3 wires (black, red, white + ground) going to your ceiling fan. One switch is for the light, the other may be a fan speed control dimmer — after having lived with it for a few months, I’m considering removing my dimmer and turning it to a simple on/off.
Even when I used the remote, the HI setting was about the speed of a normal fan’s “medium”, and the low speed didn’t do much of anything.Reverse will NOT work with this configuration. I honestly don’t think it could be achieved from the wall, period. If you really want the reverse function, best solution would be to install a small toggle on the fan itself (somewhere that won’t interfere with the blades). In step one, instead of crimping the black and thin white wire to the brown, I would crimp black and thin white to a jumper wire that supplies power to the toggle, then the toggle would feed to the brown and blue wires. I saw your post about rewiring your Altura Fan.
. Added support of 10.14 OS. By default disable data collection checkbox for Germany as per GDPR(General Data Protection Regulation).
![]()
I would love to see pictures of what you did. My wireless receiver went out and I just want to hard wire the fan to the “High” speed with downward spin only controlled by the wall switch. I’m having a little trouble following the directions from this post. Here are the wires I have.Fan sideBrownThin WhiteWhiteBlueGrayBlackPuck SideBrownThin WhiteWhiteBlueGrayBlackBlackBlue and white disconnected ( I assume for a light kit add on)My assumptionConnect Thin White, Black and Brown wires from fan side to puck side (2 blacks on puck side: do i put both in this connection? )Connect White and Blue wires from fan side to puck sideConnect Gray wires from fan side to puck side. Thanks to everyone for the help. These instructions helped me the most.I connected the thin white with brown and black.
All 3 wires into one nut. There were two black wires as well, but the one on the “corner” of the connector doesn’t go to anything on the fan side, if you can hold them up next to each other, when plugged in, theres nothing on the other end. I cut it low to keep it out of the way.So connect the thin white, black (right next to thin white) and brown on harness sideAnd grey from harness back to grey from puck sideAnd thick white and blue on fan side to thick white on puck sideLeave the blue and white that have the fancy connectors alone they are for a light connection.Again, this is all puck side, I didn’t touch the fan side (of the connector/ unaltered)Because I just cut the whole harness off, to go step by step, connecting the greys back together might be a little redundant (you can just leave the grey connected as is).
Thanks for this post.Could you confirm a few things. I have the Altura with the molex connect 9 pin connector at the fan(socket) and at the puck(pins).Once this plugged in, all wires are connected to the puck.1) I assume I cut the black, brown, and thin white wires and tie together on the fan side with a wire nut. They will no longer pass through to the puck. These wires on the puck side are not connected to anything. This sets the fan to down flow setting among other things.2)Leave the thick white and gray wires intact and will connect to the puck.3)Cut the blue wire and splice the fan side blue wire to the thick white wire. This grounds out the up flow control.4)for white ( for light ) wires, leave as is and connect to light kit white wire.5)For blue ( for light ) wire, cut from puck.a.Connect cut blue wire to one side of pull chain switch.b.Connect other side of pull chain switch to black/thin white/brown combo.
Gilmartin, Thanks for the instructional picture clearly and simply showing how to bypass the faulty Altura 68 remote reciever module. We loved the attractive, large inexpensive fan in family room.
Wasn’t looking forward to spending half the fan price for new remote receiver module. Particularly once I learned it wasn’t an upgrade but simply a replacement for original faulty equipment. Followed your diagram and done in minutes. If you find yourself in greater Houston IOU a burger and beer. Sincerely Chris Matthews. We have a model 68-ATR 68″ altura home decorator ceiling fan with no wall switch.
The fan quit operating. It’s about 4 years old but it is rarely used. The fan has power. I ordered a replacement remote receiver and capacitor from the manufacturer. I installed the new parts and I went through the proper synch procedure–still no luck.
Fan won’t operate. The remote (CHQ7078T) lights up correctly but nothing. Could the remote itself be bad? I find it difficult to believe the motor is burnt up. Thanks for your help. I hate to spend more on parts if the fan’s no good. Great thread of instructions:My fan has a bad receiver but it is not a Hampton Bay; it is a 12 year old Casablanca.
However, I am trying to do the same type of remote receiver bypass as discussed in this thread. My problem is that my wiring on the fan side is different than anything discussed in this thread. The fan is one hundred% controlled through a hand-held remote and the remote receiver; there is no wall switch. The fan has forward and reverse with 6 speeds and there is no light kit, although the fan is is wired such that the remote and remote receiver would operate if a light kit were added. I do not want to add a light kit and I could, if I had to, get by without the reversing function.The feed wires out of the ceiling and into the remote receiver consist solely of a black (live) and white (neutral), there is no ground. A wiring harness comes from the remote receiver and ends in a male 7-pin clip. A 7-pin female female clip then distributes 7 wires to the fan motor and all wires are the same thickness.
How to download age of mythology extended edition. The clips have all 7 wires in a single-line pattern. Starting from one end position and running to the other end position the wires colors are as follows: 1-white, 2-white, 3-black, 4 (middle wire)-tan, 5-red, 6-white and 7-black.
I know position 2-white and position 7-black are the feed wires from the ceiling. I also know the position 1-white and position 3-black wires go to the to optionally installed light kit. That leaves the position 4 (middle)-tan, the position 5-red and the position 6-white as currently unknown.
I am quite sure two of those wires operate the upward/downward (reversing) function and one operates the fan speeds. However I have no idea which one is which.How do I determine which is which and then how do I wire the fan to a wall-style switch.? Looking for some advice on bypassing the remote with adding a reversal switch.I am able to run the fan in the Down position by connecting the Black, thin white, and brown together and white and blue together.But when I connect the Black, thin white, and blue together and the white and brown together, my breaker trips immediately. For some reason it shorts.
Which is contradicting the information on this forum. Does anyone have a method for making the fan run in reverse?I am using a dpdt toggle switch to connect the wires in down- off – up flow positions. As far as i can tell, there should be no crossed (shorting) wires as I have it. Hey everyone, I have the Altura fan and purchased the light kit. I am able to get the light working directly with the wall switch, admittedly this is the easy part. I can’t seem to get the fan operating at all. I know this sounds stupid, especially with all the directions above.
Perhaps because i am unclear on what to do with All the wires on both sides of the harness (fan side and puck/receiver side). I would be so grateful if anyone can has the time to lay this out for me step by step for both sides of the harness (can assume fan down direction)? I have tried so many ways that I nearly have disconnected all wires from harness, sad but true. Thanks in advance.
By code, the number of conductors allowed in a box are limited depending on box size and wire gauge. Allowed in a box before adding new wiring, etc.
Check local regulations for restrictions and permit requirements before beginning electrical work. The user of this information is responsible for following all applicable regulations and best practices when performing electrical work. If the user is unable to perform electrical work themselves, a qualified electrician should be consulted.This page contains wiring diagrams for household fans including: ceiling fans and light kits, dimmer switches, fan speed controllers, 3 way fan switches, and bathroom exhaust fan circuits.The wire colors in a basic fan/light kit are typically black, blue, white, and green.
This is true of most Hunter and Harbor Breeze ceiling fans found at your local home store. The black wire is usually the hot for the fan and the blue wire is the hot for the light. The white wire is the neutral for the fixture and the green is the ground.The white wire from the fixture is connected directly to the source neutral wire, either at the fixture box or through a splice at the switch box. The ground wire is spliced to the source ground and to any outlet box terminal using a In some household circuits, the white wire may also be used to substitute for a hot wire. In these cases, it should be wrapped with black electrical tape or otherwise marked to identify it as hot.
This wiring diagram illustrates the connections for a ceiling fan and light with two switches, a speed controller for the fan and a dimmer for the lights. The source is at the switches and the input of each is From the switches, 3-wire cable runs to the ceiling outlet box. At the switch box, the black wire is splice to the output on the speed controller and at the other end to the black fan wire. The red wire is spliced to the output on the dimmer and at the other end to the blue light wire. The neutral from the source is spliced in the switch box with the white wire running to the fan and at the other end to the neutral wire on the ceiling fixture. Likewise, the ground wire is connected to any grounding terminals in the switch box and spliced to run to the fan location. Wiring Diagram Fan and Light with Source at CeilingThis diagram is similar to the previous one but with the electrical source originating at the fan/light fixture.
Three-wire cable runs from there to the controllers on the wall. The neutral wire from the source is spliced directly to the white wire on the ceiling fixture. The hot source wire is spliced to the white on the 3-wire cable and then spliced to the input wires on both controllers at the other end. The white wire is wrapped with black tape to identify it as hot. The black cable wire connects the fan to the speed controller and the red wire connects the light to the dimmer.This is the updated wiring for this arrangement with a 2-wire cable added between the fan/light and switches. The white wire is no longer used for hot and instead, the source neutral is run through to the switch box to satisfy the 2011 NEC requirement.
Two wires in this arrangement are not used, the white wire in the second cable and one of the ground wires. These should be capped at both ends with a wire nut. All other wiring is the same as in the previous diagram.
3 Way Fan Switch Wiring DiagramTo wire a 3-way switch circuit that controls both the fan and the light, use this diagram. As with all 3-way circuits, the common on one switch is connected to the hot source wire from the circuit. The common on the second 3-way switch is connected to the hot wires on the fan/light. Splice both the fan and the light hot wires together with the common wire from the SW2. The traveler wires are spliced together in the ceiling fixture box to run between switches. The travelers do not connect to the fan or light. To control the fan and light separately, a built-in switch such as a pull chain or remote control is required on the fan/light.
Ceiling Fan Dimmer Switch DiagramThis wiring arrangement allows for lowering the lights with a dimmer and controlling the fan with the built-in pull chain. The source is at the ceiling outlet box and 3-wire cable runs from there to the switch box. The neutral from the source is spliced directly to the white wire on the fan kit and the cable, running it through to the switch box. The hot source is spliced to the black fan wire and the black wire running to the dimmer. At the other end, the black cable wire is spliced to one of the hot dimmer wires, it doesn't matter which one. The other dimmer wire is spliced to the red wire in the switch box which is spliced to the blue, light wire at the other end.
Wiring a Ceiling Fan Switch LoopUse this wiring when the source is at the fixture and you want to control the feed to both components with the same switch. Three-wire cable runs from the fan to the switch box and the source neutral is spliced to the white wire and to the fan neutral. The source hot is spliced to the red wire which is connected to one terminal on the switch at the other end. The black wire is connected to the other terminal, running power back to the fan where it is spliced to both the black fan wire and the blue light fixture wire. The 3 speed fan is controlled with a pull chain switch on the fixture.Here the source is at the fan/light and a switch loop runs to the wall switch.
The source is wired directly to the fan and also spliced through to the switch. With this arrangement the light is controlled with the wall switch and the fan is hardwired for pull-chain speed control. Wiring a Fan and Light to a Single SwitchIn this wiring, the source is at the switch and 3-wire cable runs from there to the fan and light.
The source neutral and ground are spliced through to the fan location. The source hot wire is spliced to the black fan wire to hardwire it directly to the circuit and to a pigtail connecting the switch.The red wire on the 3-wire cable is connected to the switch and at the fan, it's spliced with the blue wire to the light. With this arrangement, power to the fan is controlled with a built-in pull chain on the motor housing and the light is controlled with the wall switch.Use this wiring when the power source originates at the wall box and you want to control both the fan and light with a single switch. Here the hot source is connected directly to the switch and 2-wire cable runs from there to the ceiling fan.The black wire running to the ceiling box is connected to the other terminal on the switch. At the ceiling location, it's spliced to the black and blue wires from the fan and light.
The source neutral is spliced through to the white wire on the fan. The source ground is spliced through to the ceiling box and connected to the green ground wire on the fan and to any grounding terminal found there. With this arrangement, the fan and light are turned off and on with the wall switch and the fan speeds are controlled with the built-in pull chain on the fixture. Wiring Diagram for a Bathroom Exhaust FanTo wire an exhaust fan to a wall switch, use this diagram. These fans usually come with a small electrical connection box welded to the side of the housing.
There will be a cover on the connection box that fastens with a small screw. Open it, pop the plug out of one of the wire holes and thread a wire clamp into it. Run the cable through the clamp and tighten it down.
Splice the black and white cable wires to the fan wires using a wire nut. Connect the ground to the grounding terminal in the connection box and the ground wire from the fan, if there is one. Here the exhaust fan is controlled by a timer instead of a switch. There should be two hot wires and a ground coming out of the timer casing, splice one of these to the hot source.
Spice the second to the black cable wire running to the fan. Splice the source neutral to the white cable wire. Wire the source ground to the ground wires for the switch and the fan. At the fan splice the wires, matching the colors of each, and connect the ground wire to the grounding terminal.In this arrangement a light fixture and exhaust fan are wired to the same source. The light is controlled with a single-pole switch and the fan controlled with a timer as in the previous drawing.
The hot source is spliced to each controlling device and the output of the controllers are connected at the fan splicing black to black, white to white, and the ground connecting to the terminal on the fan box. Setting Ceiling Fan DirectionCeiling fans can be set to rotate in either of two directions. This function allows for more efficient cooling in the summer and for circulating heat in the room during the winter.Fan blades are set in a slanting posture so they catch the air as they spin. The slant is down to the right and up to the left. With this attitude, a counterclockwise spin will force air down into the room creating a cooling breeze. Clockwise rotation will pull air up to the ceiling, disturbing the warm air collected there and circulating it throughout the room to warm things up.Usually there is a small sliding switch on the side of the motor housing that will control the fan direction.
Hampton Bay Fan Switch Wiring
But which way should you slide the switch for proper rotation? In most cases sliding the switch down will set counterclockwise spin, while sliding it up will set clockwise spin. So, the answer is: down in summer and up in winter. Choosing and Installing a Ceiling FanThe right size ceiling fan for your room depends on more than just the square footage or your area. Furniture, normal ambient temperature for the room, and ceiling height will all have an effect on the efficiency of the fan you choose.As a general rule, you can start with the recommended fan for a given room size as follows: For a large room of 15'x15' or more, choose a ceiling fan with a blade span of 52, 56 or 60 inches. For a 12'x12' room, go with 44 to 48 inches of blade span, and for small rooms of 8'x8' or so, a blade span of 36 inches should do the trick.Check your room space and install your fan to be 7.5 feet from the floor and 9.5 inches from the ceiling.
The distance to the nearest wall should be.5 times the span of the fan blades. If you're installing more than one ceiling fan in a room or hall, set the distance between the two at 2 times the blade span.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |